Showing posts with label LED CIRCUITS. Show all posts
Showing posts with label LED CIRCUITS. Show all posts

0 Simple LED Lamp (Current Regulated)

This simple lamp circuit is made of very few materials. It uses high intensity white LEDs. The circuit is current regulated thus the LED is protected even the supply voltage is variable. The operation of the circuit is very similar to LED driver using LM317 regulator. The current is controlled by resistor R1 with the formula: Current = 1.2V/R1
Current regulated LED lamp schematic
Part List:
C1 - 220uF electrolytic capacitor rated 16V
R1 - 27 ohms 1W
LM317 - 317 or similar regulator IC
LED - white LED (see LED pinout in case you forget)
LM317 pinout

2 Heart Beat Counter

As the heart beats, it delivers blood from (or to) the heart to the rest of the body. It is believed that as the blood flow to your veins, you skin light reflectivity varies since blood density affects skin reflectivity especially infrared (IR) lights. The simple circuit below will help us count the number of heart beat. The output pin can be connected to microcontrollers or computer to monitor the count.
schematic diagram
Positioning IR Emitter and Receiver
Part List:
R1 - 120 ohms 1/4W
R2 - 330 ohms 1/4W
POT1 - 10 kilo ohms potentiometer
LED - Infrared (IR) LED
Q1 - SY32PT or similar Phototransistor
Q2 - 2N2222, 9013, or similar NPN transistor

0 Light Detector using LED

Led is usually used as lighting indicator and display. This electronic device emits light when electricity is flowing across it. Aside from the conventional use, LED can be used also as light detector. The simple circuit below is a schematic of the detector.
schematic diagram
741 pinouts
Part List:
LED - ordinary green LED (see LED pinout for more info)
IC - LM741 or any similar op-amps
VM - volt meter
R - 3.3 Mega ohms resistor 1/4W
Bat - two pcs 9V battery

4 Roulette Circuit

This project is a simple roulette circuit made from 555 IC and 4017 decade counter. The circuit can be used for decorations and games. When the touch plate is touched, the LED will start to light up one after the other and when finger or hand is remove, the led will stop after few seconds.

Part List:

R1 - 5.6 Mega ohms 1/4W
R2 - 2.2 Mega ohms 1/4W
R3 - 10 kilo ohms 1/4W
R4 - 1.2 kilo ohms 1/4W
R5 - 560 ohms 1/4W
C1 - 2.2uF electrolytic capacitor rated 10V
C2 - 1uF electrolytic capacitor rated 10V
C3 - 100nF
LED (1-10) - red led ( see LED pinout in case you forgot)
Q1 - 9012, BC557, or similar PNP transistor
555 - LM555 or similar timer IC
4017 - 4017b decade counter
BAT - 9v battery
Touch - any conducting plates

Similar circuit:
LED chaser using 4017

4 LED Light Sequencer using 555

Another 555 IC project that will flash LEDs in such a way that light turns on in a sequence. You can use this as an indicator for turning left or right for vehicles and bikes.
light sequencer circuit
light sequence (LED1 to LED5)
Part List:
R1, R2 - 4.7 kilo ohms 1/4W
R3 - 3.9 kilo ohms 1/4W
R4, R10, R11, R12, R13 - 10 kilo ohms 1/4W
R5 -220 ohms 1/4W
R6 - 390 ohms 1/4W
R7, R8 - 500 ohms 1/4W
R9 - 560 ohms 1/4W
Q1, Q2, Q3, Q4, Q5 - 2N2222, 9013, or similar NPN transistor
LED1 to LED5 - red or any LED (see LED pinout in case you forget the pins)
C1, C3 - 220uF electrolytic capacitor rated 16V
C2 - 100nF
D1, D2 - 1N4001 or any similar diode
555 - LM555 or similar timer IC
DC -12V battery

Part List pinout:
2N2222, 9013 pinout
555 IC pinout
Similar Circuits:
LED flasher by 555 - various flasher schematic using 555 IC
LED light chaser - similar to this circuit but 10 LEDs turn on one after the other

0 Simple Darkness Detector (indicator)

What this circuit does is LED will light up when the environment is dark thus very suitable as darkness sensor or indicator. Adjusting the potentiometer R1will adjust its sensitivity. Full scale of R1 decreases its sensitivity while setting R1 to minimum makes it very sensitive.
schematic diagram
Part List:
R1 -300 kilo ohms potentiometer or any near values
R2 - 100 ohms 1/4W
LDR - any LDR
LED - red or similar LED (see LED pinout in case you forget)
Q1 - 2N2222 or similar NPN transistor
LDR jpg
2N2222 pinout

Similar Circuits:
Light activated LED driver - powered by 1.5V and light controlled
Light controlled power LED - 220VAC powered LEDs

0 Simple LED Flash Light

Small flash light uses 3V battery and 3V bulb. The problem with ordinary bulb is it consumes more power than the light it produces. Better flash light (torch) this time uses LED as the replacement of the conventional bulb. Using high brightness LED solves the power consumption problem, but the challenge now is how we can light up a high brightness LED using 3V battery since it requires more than 3V to start emitting light. The circuit configuration is very similar to two transistor flasher circuit. This simple circuit is steps the voltage up via transformer Tr to make the LEDs light up.
LED flash light circuit
NPN transistor pinout


Part List:
R1, R2 - 3.9 kilo ohms 1/4W
R3 - 22 ohms 1/4W
C1, C2 - 100nF mylar or ceramic capacitor
D1 - 1N4001 or similar diode (germanium type the better)
Q1, Q2 - 2N2222, 9013 or similar NPN transistor
Tr - any hand wound transformer ratio 1:3
LED - 2 white or any high brightness LED (see LED pinout)
DC - 3V battery (2 x AA cell)

Transformer:
You can buy a small transformer atleast 1:3 number of turns ratio or make one by just using an antenna bar or toroid core salvaged from an old cfl. Pins 1 and 2 are connected to the collector and battery source while 3 and 4 to the LEDs. Winding 1 to 2 is 10 turns #22AWG magnetic wire while 3 to 4 is 32 turns #26AWG wire.

transformer
Similar Circuits:
1.5V LED driver - can be used as torch and powered by 1.5V
LED light phototheraphy circuit - used for theraphy
Joule Thief - can be used even using "dead batteries"

0 LED light "Phototheraphy" Project


While doing a research across the web, I notice the topic about phototherapy. It says that exposure to a light at specific wavelength is beneficial to human body. This light may come from various sources such as sunlight, lasers, lamps and Light Emitting Diodes (LED). According to some studies (just read more about this on the web), that exposure to light can cure some skin disease, wound healing, hair growth, and many more.
In relation to that phototherapy idea using LED, the simple circuit below is a led driver powered by a single 1.2V or 1.5V cell. Since the voltage from a single cell is not enough to light up the LED, The circuit steps up the voltage that is enough to light up the LED (see more about the forward voltage in LED info). The circuit is basically the same with the LED joule thief  in terms on how it works, but of course with different parts.
You can use this circuit for your phototherapy session and you can direct its light to your ears, nasal airways, and other parts.


led driver schematic

Part List:
R1, R3 - 1.2 kilo ohms 1/4W
R2 - 2 kilo ohms 1/4W
C1 - 47uF electrolytic capacitor rated 3V
C2 - 470pF ceramic capacitor
L - 470uH inductor
LED - red or any low power LED (visit LED pinout in case you forgot)
Q1, Q2 - 2N2222, 9013 or similar NPN transistor

Note: There are lots of studies about this therapy but the circuit presented above has no approved therapeutic claims.

2 Wire Resistance and Continuity Tester


This circuit is similar to continuity tester using transistor but this version provides a simple estimation of the wire resistance. It can be use also as an ohmmeter to measure resistance of resistors from 0 ohms to 500 kilo ohms. The circuit has three LED indicators and the operation is summarized below.
1. All LED are ON; meaning resistance is about 0 ohm to 200 ohms.
2. Only is LED1 OFF; resistance is around 300 ohms to 10 kilo ohms.
3. Only LED 3 is ON; resistance is around 10 to 500 kilo ohms.

resistance tester schematic

Part List:
R1 - 100 ohms 1/4W
R2 - 33 kilo ohms 1/4W
R3 - 120 ohms 1/4W
R4 - 39 ohms 1/4W
R5 - 56 ohms 1/4W
LED1, LED2, LED3 - red LED (see LED info for pinout and markings)
Q1, Q2 - 2N4403 or similar PNP transistor
Probe - just use solid type wire or conductor
Bat - 3V battery

2N4403 pinout
Note: The tester is approximation only and might defer in actual results. When we say that the LED is OFF, it does not necessarily mean it’s completely off since in actual it is still emitting light.  But this light is very low enough that we can consider it as OFF.

2 Car Brake Light Circuit


A simple tail and brake light circuit for cars and vehicles using LED. When the vehicle is slowing down, switch s1 will be closed and LED will illuminate in low light. The LEDs will consume about 10mA each. When brake is applied, the switch s2 will closed and allowing the LED to illuminate at full brightness. This time the LEDs will consume 25mA current each. The circuit employs a constant current method, the same method used in the cheap power led driver circuit.
The current drawn by every LED is given by the simple equations:
Current on slowing down = 0.3/R2; and Current on brake = 0.3/R3  all current in Amperes


brake light circuit
2N2222 pinout
Part List:
R1 - 1.2 kilo ohms 1/4W
R2 - 30 ohms 1/4W
R3 - 12 ohms 1/4W
D1, D2 - 1N4001, 1N4004 or similar silicon diode
LED - red LED (3mm or 5mm) or any low power LED of your choice
Q1 - 2N2222, CS9013 or similar NPN transistor (higher power the better)
Bat - 12V car battery

Note: If your are planing to use power LEDs or modify the circuit to cater more LEDs, just replace the transistor with higher power capacity, and replace the values of R2 and R3 using the formula presented above.

2 Battery voltage monitor (12V and 6V)

The purpose of this circuit is similar to simple battery voltage indicator that provides visual indication of the battery voltage or charge.  When LED2 (red) is on, it means that the battery needs charging. On the other hand, when LED1 (green) is on, it means that the battery is in good condition. Green LED is on when battery voltage is 12V (12V version) and 6V (6V version).
schematic diagram
2N2222 and NPN transistor pinout
Part List: 6V version
R1 - 1 kilo ohms 1/4W
R2, R3, R4 - 560 ohms 1/4W
Q1, Q2 - 2N2222, CS9013, or similar NPN transistor
LED1 - green LED
LED2 - red LED
Dz - 1N5226B, or any 3.3V zener diode

Part List: 12V version
R1, R2, R3, R4 - 1 kilo ohms 1/4W
Q1, Q2 - 2N2222, CS9013, or similar NPN transistor
LED1 - green LED
LED2 - red LED
Dz - 1N5239B, or any 9.1V zener diode

Other voltage indicator circuits:
Simple Battery Voltage Indicator - uses only 1 transistor
Battery discharge indicator - improve version, uses comparator IC

6 12V emergency light using power LED

Another emergency light circuit that is very easy to construct and uses power LED not an array of LEDs unlike the simple led emergency light. The circuit is composed of two parts, the charger and the led driver. When the battery voltage is higher than the voltage of zener diode DZ + 0.7V, the charger automatically turns off (protect the battery from overvoltage).  Transistor Q4, R6, D1, D2 is the led driver circuit (See cheap led driver to know more how this circuit works).
schematic diagram
Part List:
R1 - 560 ohms 1/2W
R2 - 220 ohms 1/4W
R3 - 1 kilo ohms 1/4W
R4 - 10 kilo ohms 1/4W
R5 - 500 ohms 1/4W
R6 - value is dependent on LED power, see notes below
Q1, Q4 - TIP41C, or similar NPN Power Transistor
Q2 - 2N2222, CS9013, or similar NPN transistor
Q3 - CS9012, 2N4403 or similar PNP transistor
Dz - 12V zener diode minimum 1/2W rating
D1, D2 - 1N4001, or similar diode
Bat - 12V lead acid battery
LED - 3W white power LED
DC input - see  AC-DC converter circuit below

DC Input Supply
schematic diagram of AC-DC converter
Part List:
Transformer - 220V to 12V center tap transformer rated 10VA
D - 1N4004 or similar silicon diode
C - 1000uF electrolytic capacitor rated 25V

Value of R6
Resistor R6 will limit or control the current of the LED. The basic idea is we need to know the rated forward current for the LED. After that, we can use the formula below to determine the value of R2.
R2 = 0.8 / Current and power of R2 = Current*Current*R2
Example: 3W LED has the current rating of 530mA
               R2 = 0.8/0.530 = 1.5 ohms
               Power Rating = 0.8*0.8*1.5 = 0.96W or 1W

Parts Diagram and Pinout: click image to enlarge
TIP41C pin
2N2222, CS9013 pin
CS9012, 2N4403 pins
LED pins

Updates:
Modification below allows you to know if the battery is fully charged. When LED1 is off and circuit is connected to AC, it means the battery is charging . When battery is on, it means the battery is fully charged.
full-charge indicator
Part list Modification: (Other parts same as above)
R3 - 390 ohms 1/4W
Dz - 1N5240B or any 10V zener
LED1 - red LED or any LED with forward voltage around 2V (see LED info to know more)

0 Simple Battery Voltage Indicator for 12V Lead Acid

This simple circuit will help us monitor the voltage of a 12V lead acid battery in our vehicles. It uses only one transistor and no comparator needed unlike the battery discharge indicator circuitry.
Indicator circuit

Summary of the operation:
1. Only Red Led is on when voltage is less than 11.2V
2. Red and Green on (like orange) voltage is between 11.2V to 11.7V
3. Only Green Led is on when voltage is more than 11.7V


Part List:
D1 - 11V zener minimum 1/2W
D2 - 9.1V zener minimum 1/2W
R1, R3 - 1.2 kilo ohms 1/4W
R2, R4 - 120 ohms 1/4W
LED1 - high efficiency Red LED or any Red with 2V forward voltage
LED2 - any Green LED with 2.1V forward voltage
Q - 2N2222, BC547, CS9013 or similar NPN transistor
NPN transistor pinout
Note: You can use dual-color LED. See LED basic info to know more about the voltage drop of different LED color.

0 In-Circuit fuse tester

The idea is similar to simple voltage probe but this time it will be used to test fuse in automotive, vehicle fuses, and other DC devices. The good thing in this tester is you can test the fuse without removing it from its holder. When one of the LEDs is on, it means fuse is broken, otherwise the fuse is okay.

Part List:
R - 1.2 kilo ohms 1/4W
LED - 3mm or 5mm Red or any low power LED
P1 - probe or just ordinary wire
LED pins

Note: You can use this also in AC but the voltage is not more than 25V (AC or DC). You can use also a blown fuse indicator that is built in or embedded directly in your circuit. If you are planning to test fuses with voltages higher than 25V, I recommend using the simple voltage probe.

0 220V Led Flasher Circuit

This circuit is similar to Two Transistor LED Flasher but the only difference is it uses 220VAC as the source instead of a battery. The circuit is powered by a transformer-less ac-dc converter using a capacitor. Capacitor Cx limits the total current to 40mA and resistor Rx lessens the inrush current. Bridge diode D and capacitor C1 rectify and smoothen the DC output.
flasher schematic
Part List:
Rx - 470 kilo ohms 1/2W
R1 - 390 ohms 1/4W
R2 - 56 kilo ohms 1/4W
Cx - 470nF capacitor rated 350V minimum (use 1000V)
C1 - 100uF electrolytic capacitor rated 35V
C2 - see the capacitor vs time table
Q - 2N4401, 2N2222A and similar NPN transistor
LED - 3mm or 5mm RED or any low power LED
NPN transistor pins
LED pinout
Below is the table originally from the Two Transistor LED Flasher. The actual result in using the circuit above may vary a little but it is still a good approximation. T is the duration where the light of any LED will last or the time the LED is on.
cap C2 vs time table

Note: The circuit is powered directly to AC source thus can cause electrocution when touched. Do not build the circuit if you are new to electronics or don't have any idea at all. I suggest build the low voltage flashers below.

Other Flashers, low voltage and safer to build:
Lamp Flasher using FET - high current Flasher powered by 12V
Two transistors Flasher - very simple led flasher
1.5V flasher - powered by 1.5V flasher
Bulb Flasher
Flasher using 555 IC - flasher using lots of LEDs

0 Two transistor LED Flasher

One of the simplest led flasher circuit and that can be used as indicator circuit and decoration lighting.  Has a wide range of voltage supply ranges from 3V up to 12V DC. The circuit draws about 10mA from a 6V battery, thus consumes very low power. The parts also are minimal and very cheap. The drawback of this flasher is its good only for LEDs unlike the power Mosfet flasher that can power high power LEDs and even a 30W bulb (30W @ 12V).
Flasher Schematic
Part List:
R1 - 390 ohms 1/4W
R2 - 56 kilo ohms 1/4W
C - see Time vs capacitance table below
Q - 2N2222, CS9013 or any similar NPN transistor
LED - RED or any 3mm or 5mm low power LED
Bat - preferably 6V battery (3V to 12V will do also)
2N2222 or CS9013 pins
Flash rate:
Based on trial an error using the parts used above, the approximate flash duration T of both LED is around 0.56*R2*C.
Flash duration T diagram of  both LED
Time vs capacitance table


1 LED light chaser using 4017

This is a LED sequencer circuit where 10 led are lighting on and off after one another as if they are chasing each other .This simple circuit is  good in designing lighting   decoration in Christmas trees. This can be used in lighting animation by just adding more LEDs and drivers. The heart of the circuit is the 4017 decade counter that will give the lighting sequence in the LED. 555 timer serves as the master that gives the clock signal to the decade counter, and this ic controls the rate of the flashes depending on its output pulse frequency.

Led chaser schematic
4017 IC pins
Part List:
1- 555 IC
1- 4017b decade counter IC
R- 560 ohms (10pc)
10- LED (red, yellow, green, or orange)
R1,R3- 2k ohms resistor
R2- 20k potentiometer
R4- 1k ohms resistor
C1- 100nF capacitor
C2- 100uF electrolytic capacitor
battery 5V to 12V

You can change the rate of the flashes by just  adjusting the R2 pot resistor.  Full scale of pot is around 3 seconds light and delay in each led while zeroing R2 scale is around 400mS. Check the 555 timer calculator if you are planning to change the values of capacitor or resistor.

7 Fading LED

This a dual fading led using 555 timer IC. When first LED (Red) starts to increase its light intensity, the other LED (Blue) starts  to get dim. See the fading sequence diagram of the two LEDs below to understand how it works.
fading sequence diagram 
schematic diagram
Part list:
1-555 IC
2-150 ohms resistor
1-20k ohms resistor
1-Red LED
1-Green LED (note :Blue in diagram)
1-220uF/16V electrolytic capacitor
1-NPN transistor (2N2222, 9013, other general purpose NPN)
1-PNP transistor (9012, other general purpose PNP)
1-9V battery


1 1.5V LED driver using transistor

1.5V cell cannot light up led since it requires around 1.8V to 3.8V as forward voltage. This simple circuit will help us drive  LED using only 1.5V or even 1.2V cell.

Part List:
1-1.5V cell
1-1N4007 or any similar diode
1-2N2222 transistor or any similar NPN transistor
1-1.2k-ohms  resistor
1-220-ohms resistor
1-white LED or any bright LED
    *see LED pinout if you are not sure with LED pins

Circuit schematic and parts:
LED driver schematic
Ferrite core and transistor pins
Winding the  coil and making the ciruit :
First  look for any magnetic core for your coil. Toroidal ferrite core from old cfl is recommended (see diagram above) but still you can use any magnetic core available at hand. Using #22AWG magnetic wire wind it 30 turns and mark the starting as 1, center-tap as 2 and ending of the winding as number 3. Follow the led driver schematic above and its done.

Note: You can remove diode 1N4007 and 220 resistor and replace it with another LED. Their main purpose is mainly for suppressing excessive voltage that can damage the LED. Another similar and much better driver is the light activated led driver (joule thief) which is also powered by 1.5V cell.


1 Simple LED circuit

This circuit is very simple to make and requires only basic knowledge in electronics. We need only 3 main electronic parts, the LED, resistor and battery or dc supply.

Materials:
1- LED  (red , yellow or orange)
1- 200 ohms resistor
4 -1.5V cell (AAA or similar)
1-breadboard (optional)
1-battery holder for 4-AAA cells (optional)

Materials pins and diagram
LED pins and symbol
Resistor


1.5V AAA cells
Simple circuit schematic


LED requires around 20mA current to emits a good light. Standard red led requires 2V voltage drop or forward voltage to turn on. Since we know that our battery voltage is 6V, we can solve the value of resistance
which is equal to:
Resistance = (Vbat-Vled)/Current = (6-2)/20mA = 200 ohms

Note: You can use led resistor calculator If you are planning to use different type of LED ,battery  voltage, and different current.