Showing posts with label LED driver. Show all posts
Showing posts with label LED driver. Show all posts

0 Simple LED Lamp (Current Regulated)

This simple lamp circuit is made of very few materials. It uses high intensity white LEDs. The circuit is current regulated thus the LED is protected even the supply voltage is variable. The operation of the circuit is very similar to LED driver using LM317 regulator. The current is controlled by resistor R1 with the formula: Current = 1.2V/R1
Current regulated LED lamp schematic
Part List:
C1 - 220uF electrolytic capacitor rated 16V
R1 - 27 ohms 1W
LM317 - 317 or similar regulator IC
LED - white LED (see LED pinout in case you forget)
LM317 pinout

7 Light Activated led driver (1.5V joule thief)

This is another LED driver circuit powered by joule thief circuitry using 1.5V cell. The only difference is it has light detection that automatically turns on the led when the environment is dark.
schematic diagram

Part list:
R1 – any light dependent resistor (LDR) or photoresistor
R2 - 100 kilo ohms potentiometer
R3 – 220 ohms 1/4W
R4 - 120 kilo ohms 1/4W
R5 - 2 kilo ohms 1/4W
Q1 - 9012, 2N4403, or any similar PNP transistor
Q2, Q3 - 2N2222, 9013, or any similar NPN transistor
C - 22pF to 47pF capacitor
L - any 100uH to 1mH inductor
LED - any type of LED  (see LED pinout in case you forgot)


Part list diagrams: Click to diagrams to enlarge
PNP transistor pins
NPN transistor pins
LDR

You can adjust sensitivity of the light detector by varying the value of potentiometer R2. Full value of R2 means highest sensitivity.

Note:  see Sir Acme Fixer recommendation on how to construct the joule thief in the comments section below.

13 Cheap LED driver using 7805 regulator

This circuit is another easy to build Led driver that uses 7085 IC regulator and  resistor. Can power led from 0.5W to 3W (5w is also doable) with a wide range of input voltage from 9V to 15V. Current delivered to the led is controlled by the resistor only. Meaning if you plan to change the current capacity (power capacity) of the driver, just replace the value of resistance using the following formula:
R = (5-Vled) / I;    where I is the current and Vled is forward voltage specified by LED manufacturer and can be found in its datasheet.
For example:
300mA current is needed to power up a 1W LED with voltage drop of 3.3V. You will have:
R = (5-3.3)/0.7 =  5.66 or around 5.6 ohms
driver using 7805
Part List:
1-7805 regulator
1-resistor
    - 5.6-ohms 1/2W for 1W led
    - 2.0-ohms 2W  for 3W led

Note: The maximum current of the 7805 regulator is around 1.5A only but you can modify it to increase its current capacity (see High current 7805 to know how it is done). Take note also the values of current and forward voltage of LED based on the manufacturer's datasheet. Then use the formula above to determine the value of resistor.

Other LED drivers:
1. Simple LED driver using LM317 regulator – simplest using 2
main electronic parts, resistor and IC
2. Cheap Power LED Driver circuit – cheapest, uses only resistor, transistor and diode.
3. High current LED driver using FET – simple, high power and very stable led driver.

27 High current LED driver using FET

This led driver uses a constant current circuit using N-channel power mosfet. What this driver do is it delivers constant current through the LED thus protecting it from damage and at the same time maintaining the output power and output light of the LED. The magnitude of current is controlled  by R2 and the voltage of base-emitter of transistor Q1. In equation form:
Current(in LED) = 0.7/R2  or R2 =0.7/Current; where this current is the operating current of the LED.
LED driver  schematic
Part List:
R1- 1 kilo-ohms resistor 1/2W
Q1- 2N2222 NPN transistor or similar
Q2- IRF530 power mosfet, or similar
DC- 9V to 15V DC
See values of R2 on every LED current and power rating in resistance table below. R2(actual) is the value used in actual circuit.

R2 resistance  table
Transistor pinouts:
IRF530 pinout
2N2222 pinout
Paralleling Power LEDs
If you are planning to use more than 2 LEDs, lets say about 16 power LEDs. We can modify the circuit by simply adding some resistors in our original driver. The value of R is 0.33 ohms 1/2W to 1W. The value of R2 is dependent on the LED current rating and the same values in resistance table above.
How it is done:
For example you have 16pcs of  1W power leds. The leds will be arranged 8 rows with 2 series led per row. You will need also 8 resistors R and 8 resistors  R2. The value of R2 is 1 ohm @ 1W based on the table above. R2 will be connected in parallel together, same as diagram below.
LED driver with parallel LEDs
Other LED drivers:
1. LED driver using 7805 regulator –one of the cheapest and simplest driver
2. Simple LED driver using LM317 regulator – simplest using 2 main electronic parts, resistor and IC 
3. Cheap Power LED Driver – cheapest, uses only resistor, transistor and diode

13 Simple LED driver using LM317 regulator

This Led driver is very easy to construct since  you will need only 2 electronic parts, the LM317 IC regulator and 1W resistor. Driver can be powered by any 9 to 20V DC supply. Circuit can drive any  LED ranging from .5W up to 5W by just replacing the value of resistor depending the allowed current specified for the LED using the formula shown below : ( no need for LM317 Calculator).
R =1.25/current(I);    where I is the current specified by LED datasheet
For example:
700mA current is needed to power up a 3W LED, you will have:
R=1.25/0.7A=1.785 or around 1.8-ohms
LED driver circuit
Part List:
1-LM317 regulator
1-resistor
    -3.9-ohms for 1W led
    -1.8-ohms for 3W led

Other LED driver:
1. LED driver using 7805 – one of the cheapest and simplest driver, similar to this driver
2. Cheap Power LED Driver circuit – cheapest, uses only resistor, transistor and diode
3. High current LED driver using FET – stable and  high current led driver

Note: The maximum current of the LM317 regulator is around 1.5A only. Don't forget to add heatsink in the regulator to avoid damage due to overheating. When the DC supply is not regulated, add a 100uF (or higher) capacitor accros  the input positive and negative terminal.

17 cheap Power LED Driver circuit

Driver for power led can cost you several dollars.We decided to design a very simple driver that is very cheap to construct, but can drive your power led well.
driver schematic diagram
2N3055 pin and symbol
materials:
DC-power supply  9V-15V DC
Q1-2N3055 or similar NPN transistor
R1-220-ohms 1W
D1,D2-1N4001 or any  silicon diode
R2 @ 1W LED -2.7ohms 1W
R2 @ 3W LED -1.5-ohms 1W
R2 @ 5W LED -0.6-ohms  or 2 x 1.2-ohms/1W in parallel

The circuit employs a simple constant current circuit that limits the current that will flow through the power led. It is very easy to modify if you change the wattage of your led by just replacing the value of R2. You can use also a DC supply of any voltages from 9V to 15V.
For other LED power rating just use the approximate formula:

Current (I) =0.8/R2; where I is the current specified by LED manufacturer. Maximum value of I in this driver is 10A.
Use the formula  R2 = 0.8/Current(I) to determine R2.
This led driver is used in 12V power LED emergency light circuit, of course with some modification.
Other led drivers:
1. driver using 7805 - simple and cheap
2. LED driver using LM317 - simple and cheap
3. High current LED driver using FET - stable and high current capacity.