Showing posts with label mobile phone related. Show all posts
Showing posts with label mobile phone related. Show all posts

1 Mobile Phone Detector

This project is a simple mobile cellphone detector circuit. As the phone receives or sends massage or call, it sends off signal. The emitted signal will be detected by the circuit and will cause the LED to light up and the buzzer to sound. You can use this circuit as decoration to your cellphone or use this as a detector to unauthorized use of cellphone in prohibited area. Any cellphone activities like sending or receiving SMS, sending videos or any form of data transmission can be detected by this simple circuit. R5 and C7 set the duration of the buzz and ON time of the LED for 1 sec (you can modify it using the 555 timer calculator in monostable mode). Click diagram to enlarge.
phone detector circuit
Part List:
R1, R2 - 2.2 Mega ohms 1/4W
R3, R6 - 1.2 kilo ohms 1/4W
R4, R5 - 10 kilo ohms 1/4W
R7 - 100 kilo ohms 1/4W
C1, C2 - 22pF ceramic capacitor
C3, C7 - 47uF electrolytic capacitor rated 16V
C4 - 220nF
C5 - 33pF ceramic capacitor
C6 - 4.7uF electrolytic capacitor rated 16V
C8 - 100nF
ANT -  just a piece of conductor less than 1ft
Q1 - 2N2222 or similar NPN transistor
LED - red led (see LED pinout in case you forgot)
Buz - 12V buzzer
555 - LM555 or similar timer IC
IC - CA3130 or similar
Bat - 9V to 12V battery

Parts pinout: click diagram to enlarge
CA3130 pins
555 pinout
2N2222 pinout

0 iPhone Charger circuit

iPhone charger not supported


You might  wonder why you can't charge your iPhone using the ordinary USB charger you bought. According to some sources across the web, iPhone charging scheme uses all the 4 pins of the usb port including the data lines. This simple iPhone charger  can be constructed by adding only some resistor combinations across the USB data lines.

USB port  pins
iPhone Charger circuit (500mA)
This is an ordinary iPhone charger that can be use if you are not in a hurry. Can charge your iPhone around 3 hrs if you are using high capacity battery (1420 mAh).

500mA iPhone charger circuit
Materials:

5V regulated DC supply like on your computer PSU
2-150k 1/4W
2-100k 1/4W
Note: make sure that your supply is regulated and can deliver atleast 500mA current.

iPhone Fast Charger circuit (1A)

This is a fast charger allows your iPhone to be charged around 1A current or making your iPhone fully charged around one and half hour for 1420 mAh rated (high capacity) battery.



Fast charger schematic

Materials:
5V regulated supply like on your computer PSU
1-150k 1/4W
2-100k 1/4W
1-120k 1/4W
Note: make sure that your supply is regulated and can deliver atleast 1A current.


Note: circuit above is considered working, but use it at your own risk.

2 USB charger circuit

This simple usb charger is powerd by any battery or dc supply with an input ranges from 7.5V up to 25V DC. It is very handy, portble and easy to build since uses only at least 3 electronic components.

Materials:
1-7805 regulator IC
1-USB female socket
wire
battery 7.5V  to 25V or DC supply

optional materials:
C1 - 10uF/25V electrolytic capacitor
C2 - 10uF/10V electrolytic capacitor

Charger diagram and pinouts:


7805 regulator pinouts
USB pins and Functions
USB cable and Device pinouts
Charger Schematic diagram
You can use this charger to charge your cellphones, iPod, mp3 players or any devices that uses USB power as its charging source or supply.

39 Mobile Cell phone Charger project

Cell phone charging is a problem when you are away from home or where main source is not available. A fully charged phone may last its battery up to 3 to 8 hours depending how it is used. When you are out for picnics, camping, and or having adventure with your cell phone battery empty, you cannot receive calls, take pictures or listen to music, thus a simple and portable mobile charger is a need.
A good charger has an output of 4V DC to 8V DC and a current capacity of 100mA up to 500mA.With this charger capacity, standard 3.7V at 850mA battery can be charged up to 2 hours to 4 hours.
In this project, the charger can deliver a current up to 240mA which can fully charge a cell phone in about 3.5 hours. For the charger to be portable and handy, the electronic parts are minimal and powered only by a single 9V battery with only 3 to 5 cheap parts.
charger schematic
Part List:
9V battery (preferably chargeable)
Light Emitting Diode (LED) - any color yellow, red, or orange
R1 - 2 kilo-ohms resistor or use 1k when not charging
R2 - 220 ohm resistor
D1 - 1N4001 diode or similar
Q1 - 2N2222, 9013 or similar NPN transistor,
 wires and charger jack.

The use of LED and 220 ohm resistor is to provide output indicator of the charger.1N4001 diode protects the cell phone battery from draining its charge. Transistor and 2k resistor limits the charging current to 250mA max.

Improved and simplified charger
improved charger
What this charger do is deliver a constant current to your cellphone and its  input supply can be extended form 9V up to 12V.
Part list:
LED - yellow or orange color LED
R2 - 560 ohms 1/2W
Transistor - 2N2222 , 9013 or similar NPN transistor, wires, charger jack
R1- value is dependent on maximum charging current.
    - 5 ohms for 300mA
    - 3.3 ohms for 450mA , and
    - 3 ohms for 500mA

Feel free to replace any parts with any of the same specification. Build it and enjoy.

Note: If you have problem with the charging using version 1 charger replace 2K resistor to 1K and remove the LED and 220 ohms resistor. If you are planning to build a more "all purpose type charger" which is cheap and can charge different battery voltages with different charging current, try universal charger circuit.


10 cell phone charger using 1.5V battery

Have you ever experienced going to other place and suddenly your cell phone turn off, and no power is available for you to charge your phone? Then try building this portable and emergency cell phone charger powered by 1.5V battery.



Charging your cell phone by 1.5V battery, how? 


For the cell phone to charge, charger output must be above 4V and can deliver a maximum current of 500mA. This charger circuit will step up the voltage from 1.5V to 5V DC to reach the cell phone charging requirement. The circuit uses only an AA or AAA 1.5v battery (1V to 2.4V).  The charger is composed of simple oscillator, a rectifier, and voltage regulator. The feedback winding F is composed 5 turns of #30 AWG magnetic wire and main winding P is composed of 6 turns of #24 AWG wire. The 5.1V zener diode and 2200uF capacitor regulates the output voltage to ensure proper charging.

The windings are not critical, you can experiment using different number of turns. If ever the charger doesn’t have any output, try to reverse the winding connection.

Note: This charger is functional but provides no warranty on its accuracy. Try building at your own risk.